VFR radio calls at a towered airport: a complete flight, call by call

By , pilot · Published · 8 min read

Quick answer

A towered VFR flight follows the same chain of calls: ground for taxi, tower when ready, line up and wait, takeoff, leaving the airspace, inbound call with position and altitude, pattern entry, landing and taxi back. Read back runways and hold short instructions, never enter a runway on a taxi instruction, and switch to ground only when told.

One flight, every call

Earlier articles covered the building blocks: the phonetic alphabet, numbers, how a radio call is structured and readbacks. This one puts them together in a local VFR flight from a towered airport: ground, runway, departure, return, traffic pattern, landing and taxi back.

The calls below follow FAA usage, from the Aeronautical Information Manual (AIM), chapter 4, and the controller phraseology in FAA Order JO 7110.65. Where ICAO phraseology (used in Europe and most of the world) differs, it's flagged and summarized in a table at the end.

The examples use a made-up airport, "Springfield", and the call sign N123AB, spoken CESSNA ONE TWO THREE ALFA BRAVO. Frequencies, runways and VFR checkpoints are illustrative: always use your sectional, the Chart Supplement and the ATIS.

Tip: listen to the ATIS before your first call and note the letter, runway in use and altimeter. Telling the controller "with information Bravo" saves a whole exchange.

1. Calling ground for taxi

AIM 4-3-14 says departing pilots should call ground control (or clearance delivery) before starting engines. AIM 4-3-18 lists what a taxi request contains: aircraft identification, location on the airport, type of operation (VFR or IFR) and point of first intended landing. For a local flight, say what you plan to do instead.

WhoMessage
PilotSPRINGFIELD GROUND, CESSNA ONE TWO THREE ALFA BRAVO, AT THE FBO, VFR LOCAL TO THE NORTH, WITH INFORMATION BRAVO
GroundCESSNA ONE TWO THREE ALFA BRAVO, SPRINGFIELD GROUND, RUNWAY TWO SEVEN, TAXI VIA ALFA, HOLD SHORT OF RUNWAY THREE ONE
PilotRUNWAY TWO SEVEN, TAXI VIA ALFA, HOLD SHORT OF RUNWAY THREE ONE, CESSNA THREE ALFA BRAVO

Three points from AIM 4-3-18 that trip up students:

  • ATC never uses the word "cleared" for taxi. A taxi instruction to runway 27 does not authorize you to enter or cross runway 27 itself
  • Every runway crossing needs an explicit clearance
  • You should always read back the runway assignment, any clearance to enter a runway, and any hold short or line up and wait instruction. Controllers are required to get a readback of hold short instructions

If you don't know the airport, ask for progressive taxi and ground will give you step-by-step directions.

ICAO difference: the ICAO standard taxi instruction is TAXI TO HOLDING POINT (number) RUNWAY (number), and the reply to HOLD SHORT is HOLDING SHORT. In ICAO phraseology ROGER or WILCO is not an acceptable answer to HOLD, HOLD POSITION or HOLD SHORT.

2. At the runway

Once the run-up is done, AIM 4-3-14 says to switch from ground to the tower (local control) frequency when you're ready to request takeoff clearance.

WhoMessage
PilotSPRINGFIELD TOWER, CESSNA ONE TWO THREE ALFA BRAVO, HOLDING SHORT RUNWAY TWO SEVEN, READY FOR DEPARTURE, VFR TO THE NORTH
TowerCESSNA THREE ALFA BRAVO, RUNWAY TWO SEVEN, LINE UP AND WAIT
PilotRUNWAY TWO SEVEN, LINE UP AND WAIT, CESSNA THREE ALFA BRAVO

Under JO 7110.65 3-9-4, the controller states the runway first and then LINE UP AND WAIT, and an aircraft shouldn't sit in that position more than 90 seconds without further instructions. If you've been waiting a while, it's fine to remind the tower you're on the runway.

ICAO difference: ICAO lets controllers issue conditional line-up clearances ("behind the landing Cessna, line up and wait behind") when pilot and controller both see the traffic. The FAA does the opposite: JO 7110.65 3-9-4 tells controllers not to use conditional phrases such as "behind landing traffic" for line up and wait.

3. Takeoff

JO 7110.65 3-9-10: runway number first, then the clearance.

WhoMessage
TowerCESSNA THREE ALFA BRAVO, RUNWAY TWO SEVEN, CLEARED FOR TAKEOFF
PilotRUNWAY TWO SEVEN, CLEARED FOR TAKEOFF, CESSNA THREE ALFA BRAVO

AIM 4-3-18 adds a habit worth keeping: once you're cleared onto the active runway, a single pilot should monitor only ATC frequencies until clear of the Class B, C or D surface area, and do the same from landing clearance until the taxi is complete.

4. Leaving the airspace

The tower may ask you to report a VFR checkpoint or simply let you go. Here the FAA and ICAO habits really diverge.

AIM 4-3-2 says it's good practice to stay on tower frequency until you're out of the surface area to hear traffic information, but you don't need to ask permission to leave the tower frequency once you're outside it.

ICAO difference: under EASA SERA (SERA.14060) you must tell the ATS unit before changing frequency if it hasn't told you to, and you'll often be asked to report published VFR exit points. Expect REQUEST CHANGE TO (frequency) and FREQUENCY CHANGE APPROVED.

5. Coming back

Class D needs two-way radio communication before you enter (AIM 3-2-5). Arriving pilots call the tower with their position, altitude, destination and requests, far enough out that they don't enter the airspace before contact. AIM 4-3-2 suggests the initial call about 15 miles from the airport.

Per AIM 3-2-5, if the tower answers with your call sign, even "(call sign), standby", communication is established and you may enter. "Aircraft calling Springfield Tower, standby" or "remain outside the Class Delta airspace" means you may not.

WhoMessage
PilotSPRINGFIELD TOWER, CESSNA ONE TWO THREE ALFA BRAVO, ONE FIVE MILES NORTH, THREE THOUSAND FIVE HUNDRED, INBOUND FOR LANDING WITH INFORMATION CHARLIE
TowerCESSNA ONE TWO THREE ALFA BRAVO, SPRINGFIELD TOWER, ENTER LEFT DOWNWIND RUNWAY TWO SEVEN, REPORT LEFT DOWNWIND
PilotENTER LEFT DOWNWIND RUNWAY TWO SEVEN, WILCO, CESSNA THREE ALFA BRAVO

JO 7110.65 3-10-1 lists the landing information the tower gives: pattern instructions (ENTER LEFT/RIGHT BASE, MAKE RIGHT TRAFFIC, MAKE STRAIGHT-IN, which may be left out if you'll just circle left), runway, wind and altimeter. If you've heard the ATIS, say the code and the tower can skip it. "Have numbers" only means you have runway, wind and altimeter, not the ATIS.

ICAO difference: the ICAO pilot call is (position) (level) FOR LANDING, or INFORMATION (code) FOR LANDING with ATIS. The tower answers JOIN (position in circuit) with the runway and QNH in hectopascals.

6. In the pattern

Unless told otherwise, fixed-wing traffic circles the airport to the left (AIM 4-3-2). AIM 4-3-3 recommends entering at 1,000 ft AGL for propeller aircraft unless the Chart Supplement publishes another pattern altitude. The legs (upwind, crosswind, downwind, base, final) double as reporting points.

For sequencing, JO 7110.65 3-8-1 gives the tower NUMBER (sequence), FOLLOW (traffic), EXTEND DOWNWIND, MAKE SHORT APPROACH, CIRCLE THE AIRPORT and MAKE LEFT (or RIGHT) THREE-SIXTY or TWO SEVENTY.

WhoMessage
PilotSPRINGFIELD TOWER, CESSNA THREE ALFA BRAVO, LEFT DOWNWIND RUNWAY TWO SEVEN
TowerCESSNA THREE ALFA BRAVO, NUMBER TWO, FOLLOW THE PIPER ON BASE
PilotNUMBER TWO, TRAFFIC IN SIGHT, CESSNA THREE ALFA BRAVO

Training in the pattern? AIM 4-3-23 describes "cleared for the option": request it entering downwind and you may then do a touch-and-go, low approach, missed approach, stop-and-go or full stop. It's only used at towered airports and is subject to ATC approval. For repeated circuits you can also ask for closed traffic (JO 7110.65 3-10-11).

ICAO difference: ICAO pilots report FINAL at 4 NM from touchdown and LONG FINAL when turning final further out (or 8 NM on a straight-in). The option approach is a US procedure; ICAO towers clear you for TOUCH AND GO or ask you to MAKE FULL STOP.

7. Landing

JO 7110.65 3-10-5: RUNWAY (number) CLEARED TO LAND. If the runway changes, you'll hear CHANGE TO RUNWAY (number) first, so the switch doesn't slip past you.

WhoMessage
TowerCESSNA THREE ALFA BRAVO, RUNWAY TWO SEVEN, CLEARED TO LAND
PilotRUNWAY TWO SEVEN, CLEARED TO LAND, CESSNA THREE ALFA BRAVO

No landing clearance by short final? Ask, or go around. GO AROUND is the controller instruction in JO 7110.65 3-8-1; in ICAO phraseology the pilot answers GOING AROUND.

8. Clearing the runway and taxiing in

AIM 4-3-21 is specific:

  • Exit at the first available taxiway, or where ATC told you, and don't turn onto another runway unless authorized
  • You're clear of the runway once every part of the aircraft is past the runway holding position markings. Then stop unless ATC has told you otherwise
  • Don't switch to ground until the tower tells you to (AIM 4-3-14). Ground's taxi clearance to parking doesn't authorize you to enter or cross any runway
WhoMessage
TowerCESSNA THREE ALFA BRAVO, TURN RIGHT ON CHARLIE, CONTACT GROUND POINT SEVEN
PilotRIGHT ON CHARLIE, GROUND POINT SEVEN, CESSNA THREE ALFA BRAVO
PilotSPRINGFIELD GROUND, CESSNA ONE TWO THREE ALFA BRAVO, CLEAR OF TWO SEVEN AT CHARLIE, TAXI TO THE FBO
GroundCESSNA THREE ALFA BRAVO, TAXI TO THE FBO VIA CHARLIE, ALFA
PilotTAXI TO THE FBO VIA CHARLIE, ALFA, CESSNA THREE ALFA BRAVO

"Ground point seven" means 121.7: AIM 4-3-14 lets the controller drop the "121" when the frequency is in that band.

ICAO difference: ICAO towers may ask you to REPORT RUNWAY VACATED, which you say once the whole aircraft is beyond the relevant holding point. The typical handoff is WHEN VACATED CONTACT GROUND (frequency).

ICAO vs FAA at a glance

PhaseFAA (US)ICAO / EASA SERA
TaxiRUNWAY (number), TAXI VIA...TAXI TO HOLDING POINT (number) RUNWAY (number) VIA...
Hold short replyRead back the hold shortHOLDING SHORT (ROGER and WILCO not acceptable)
Conditional line upNot used for line up and waitAllowed when both see the traffic
Leaving the towerNo permission needed once outside the surface areaTell ATC before changing frequency
JoiningENTER LEFT DOWNWIND, MAKE RIGHT TRAFFIC, STRAIGHT-INJOIN (position in circuit)
Pressure settingAltimeter in inches of mercuryQNH in hectopascals
Training circuitsCleared for the option, closed trafficTouch and go, make full stop
After landingClear of hold markings; ground only when toldReport RUNWAY VACATED if asked

Common mistakes

  1. Entering the departure runway on a taxi instruction. Taxi to a runway is not a clearance onto it
  2. Answering ROGER to a hold short instruction instead of reading it back
  3. Calling the tower already inside Class D, or entering when the tower answered "aircraft calling, standby" without your call sign
  4. Saying "have numbers" when you haven't heard the ATIS
  5. Switching to ground on your own after landing
  6. Stopping on the runway once you've slowed, instead of clearing the hold markings

How to practice

  • Write out the calls for your home airport with its real frequencies and checkpoints, and say them aloud before you fly
  • Drill the replies that fall apart under pressure: hold short readbacks, line up and wait, number two, traffic in sight
  • After each flight, replay it phase by phase and note the call where you hesitated

If you want to fly the whole sequence with a controller who answers back, you can practice it in KoAir, in English or Spanish.

Frequently asked questions

Does a taxi instruction to a runway let me enter it?

No. AIM 4-3-18 says taxi instructions to the assigned runway don't authorize you to enter or cross it. You need line up and wait or a takeoff clearance.

When should I make my first call to a Class D tower?

Before entering the airspace, with two-way communication established. AIM 4-3-2 suggests about 15 miles out, giving position, altitude, destination and request.

Does 'have numbers' mean I have the ATIS?

No. It only tells the tower you have runway, wind and altimeter (JO 7110.65 3-10-1). Give the ATIS code if you've listened to it.

Do I need permission to leave the tower frequency?

In the US, not once you're outside the Class D surface area (AIM 4-3-2). Under EASA SERA you tell ATC before changing frequency.

What does 'cleared for the option' mean?

A US procedure that lets you choose a touch-and-go, low approach, missed approach, stop-and-go or full stop. Request it entering downwind at a towered airport (AIM 4-3-23).

Sources

  1. FAA Aeronautical Information Manual (AIM), Chapter 4, Section 3: Airport Operations, 4-3-2 Airports with an Operating Control Tower; 4-3-3 Traffic Patterns; 4-3-14 Communications; 4-3-18 Taxiing; 4-3-21 Exiting the Runway After Landing; 4-3-23 Option Approach
  2. FAA Aeronautical Information Manual (AIM), Chapter 3, Section 2, 3-2-5 Class D Airspace (arrival entry requirements)
  3. FAA Order JO 7110.65, Air Traffic Control, 3-8-1 Sequence/Spacing Application; 3-9-4 Line Up and Wait; 3-9-10 Takeoff Clearance; 3-10-1 Landing Information; 3-10-5 Landing Clearance; 3-10-9 Runway Exiting; 3-10-11 Closed Traffic
  4. Spain, Real Decreto 1180/2018, Annex V (ICAO standard phraseology, Spanish and English), 1.4.8 Taxi; 1.4.9 Hold (note on HOLDING / HOLDING SHORT); 1.4.11 Line up and conditional clearances; 1.4.14 Joining the circuit; 1.4.16 FINAL and LONG FINAL; 1.4.17 Touch and go, full stop
  5. Spain, Real Decreto 1180/2018, Annex V (ICAO standard phraseology, Spanish and English), 1.4.21 Runway vacating
  6. Commission Implementing Regulation (EU) 2016/1185 amending SERA (923/2012), SERA.8015 ec) Conditional clearances; SERA.14060 Transfer of VHF communications
  7. UK CAA CAP 413 Radiotelephony Manual, Chapter 4 Aerodrome Phraseology (circuit reports, sequencing, touch and go, runway vacated)

Reviewed by Edel González, pilot, on November 6, 2026.

Drafted with AI assistance.

Educational content: in flight, always follow ATC instructions and the current AIP.

How we write these articles. Every article starts from official documents (ICAO, EASA/SERA, FAA) cited at the end. AI helps with drafting; phraseology, numbers and codes are checked by a person before publishing.

Practice these calls out loud

Radio practice in English and Spanish for microlight and PPL pilots, with ATC audio. Lessons of about five minutes, on your phone.

Download on the App StoreGet it on Google Play